How to Hang a Picture on a Brick Wall?
Mounting tapes as well as the adhesive can be used for hanging lightweight pictures on brick. For heavier picture frames brick hooks can be used. These hooks can carry a load of around 30 pounds, without any damage to the brick.
In order to hang heavy picture frames, drilling mounting hooks in the wall will become necessary. Is the beauty of exposed bricks ruined when pictures are hung? No that is not the case. The frames will instead enhance the beauty of the brick wall.
The weight, dimensions, and location of placement of the frame should be known first then the suitable method should be selected for hanging the picture. Since all methods will not be suitable for all frames. Brick-wall works are more permanent as compared to wood if holes are drilled.
Best Way to Hang Pictures on a Brick Wall
After the required spot is identified and the dimensions are known, then the right mounting equipment is to be chosen. Mainly we have three types of hardware for hanging pictures on brick walls. These are adhesive hooks, hard wall hangers & masonry hooks.
For determining the perfect mounting method, you must ask yourself some required questions:
- Whether you are permitted to permanently drill into the brick wall?
- The span of hanging the photo. Is the photo required to be mounted permanently or temporarily?
- What is the dimension of the picture?
- What is the weight of the picture?
- What is your available budget?
It is very much necessary to determine which mounting method is the best suited for your frame.
Some Relate “Wall” Article Are as follows.
- Frost Wall
- Pony Wall
- Cmu Wall
- Parapet Wall
- What Is Drywall
- Wall Paint Finishes
- Gabion Wall Cost
- What Is a Shear Wall
- Types of Partition Wall
- Alternatives to Drywall
- How to Find Wall load
- Mount TV on Brick Wall
- Disadvantages of Wall Putty
- Weep Holes in Retaining Wall
- Pros and Cons of Sealing Brick
- Bathroom Half Wall Panels
- Long Wall Short Wall Method
- Cost to Repair Drywall Ceiling Water Damage
- How to Cover Concrete Walls in Basement
How to Install Adhesive Hooks on a Brick Wall?
Adhesive hooks are quite easy to be hung on walls. Just some stepwise processes should be followed to make sure that the hooks are rigidly fixed to the brick.
Clean the Brick Before Placing
If the surface is cleaned properly then the glue on the adhesive hook will stick much better. The dust prevents the glue from properly holding.
Mark the Spot for Placing the Hook
A pencil should be used to mark the spot before sticking the hooks. The marking should be properly visible and perfectly leveled.
The marking for sticking the hooks should be done in such a way that the hook will be placed on the center of the brick and not on the mortar line, for proper strength.
The adhesive must also not be placed half on brick and half on mortar line as then also proper strength will not be attained.
Stick the Hook to the Wall
The plastic cover will have to be removed from the adhesive anchor, protecting the glue. Then without touching the adhesive properly with care, the anchor is pressed on the brick wall for near around 30 seconds.
The plastic cover is given to protect the glue, and after opening the cover for use the glue is not touched by fingers because the oil and dirt present in our fingers will weaken its strength.
Will pressing the hook it should be placed on the marked region and should not be pressed very hard just a proper pressing strength should be applied.
Let the Adhesive Properly Dry
After sticking the hook, adequate time of around 30-60 minutes should be given, before the frame is to be hung. After the specified time you can hang your required picture.
Hard Wall Hangers
Hard wall hangers are manufactured to be used on concrete, block, and brick walls. These hangers have medium strength and can carry loads of 25 pounds or 11kg. This strength is nearly around double the strength of the adhesive hanger.
This process is quite fast and easy. Sturdy pins anchor the base into the wall.
How to Install Hardwall Hangers on a Brick Wall?
Hard wall hangers can be installed on top of brick mortar depending on how they are installed on brick walls.
In case the mortar flushes with the brick face, it can be used to hold the hanger, whereas if the mortar sticks out from the surface, or it’s not at par with the outer surface of the brick then not fix the hanger on the mortar instead fix it on brick.
Mark the Spot for Hanging
Perfectly spot the position and mark the place for hanging, which should be straight. This hanger happens to be a permanent type, so proper time should be invested in picking the spot and marking it as required.
Installing the Hangers in Position
The hanger is placed on the pre-marked spot, and with the help of hands, they are positioned so that they do not move. Then with the help of the other hand, the four pins are nailed.
In the beginning, the pins are to be nailed just halfway. It is done so that it can be checked that the hooks are still maintaining their position, then if it’s so hammer the nails totally. If by any chance the hooks do not stay in the perfect region. It needs to be removed and then again adjust.
Proper time should be taken for properly hammering the pins while hammering it should not be done too hard. It is done slowly so that the hook will remain in position and helps in preventing accidents.
Hang the Required Picture Properly
By making sure the frame is straight, hang the picture properly. The proper picture should be placed like an extra heavy weighted picture should not be placed.
- All About Pavers | What Are Pavers | Types of Pavers and Cost | Most Popular Brick Paver Colours | Most Popular Brick Paver Colours
- What Is Paint Finishes for Walls | Types of Paint Finishes | Types of Paint Finishing
- How to Use Rate Analysis of Brick Work Calculator| Rate Analysis of Brick Work Calculator
Amongst all masonry anchor is the strongest and enduring method. They have a holding capacity of about 10 times the carrying capacity of hard wall hangers and nearly around 30 times the capacity of adhesives.
They are available in variable styles and sizes. Different varieties can be used for different required purposes. A pothole is required to be drilled into the brick wall before the anchor is to be secured.
Due to its complex procedure, they become costly, and skilled labor is required. At the same time, they are most safe and protected. After drilling the hole into brick, it can not be undone. But at the same time if the mortar is drilled then that can be redone or repaired.
Use the Right Tools
For drilling a pilot hole into a brick wall special tools will be required. Any type of drill can be used for carrying out the job if the perfect bit is present. But hammer drill is preferable because their back-and-forth action provides a good outcome.
Having a hammer drill and brand-new bit will help properly drill into both bricks as well as mortar. The drilling should be done patiently, the total depth should not be drilled at once. After drilling a little portion, it should be cooled down and then again drilled.
Mark and Then Hole Is Drilled
The spot should be marked before drilling is started. Being permanent in nature the location must be perfect because later it cannot be adjusted.
Time should be taken while drilling. While drilling press hard the drill, this pressure is applied so that the hammering action comes to play properly. While drilling the hands should be kept straight, do not make any angle while drilling.
The Anchor Is to Be Placed in the Hole
After drilling the hole, then place the anchor in it. Many of the anchors will need a plastic piece in the hole with a screw. The plastic is to be hammered gently and then a screw is installed.
While hammering the plastic it should not be hammered too hard and deep. If the anchor is hard to be tapped, then the hole might have been drilled too narrow, or it may be deep enough, which should be re-adjusted.
Installing the Screw
It will be the easiest part of the task; the screw must be just driven in. For this job, you will need a screwdriver. The hand can also be used for driving the screw.
The whole length of the screw should not be driven in, some portion should flush out. The small bit of space between a brick wall and the screw head will allow the picture to be adjusted as required.
Hanging Pictures on a Brick Wall
While hanging pictures on brick walls, some knowledge about brick itself should be kept in our minds. The characteristics of the brick guide the fact that how much the adhesive or anchor will be effective, because some bricks may be smooth and dense, while some might be rustic in nature. So, proper inspection should be done beforehand.
Different-sized bricks are available in the market, so a proper brick hook must be brought that will be correctly sized for the brick on which work is to be done.
Hammering should not be directly done on brick, rather it should be done on mortar. It is so done because if the brick gets damaged, then after replacing the brick it might happen that the new brick quality is not matching with the old one. Then it will be a problem, but, on the other side if the mortar is damaged it can be easily replaced.
While drilling it should be done slowly, and make sure to drill in the center do not do it at the edges, as it will increase the risk of damage.
Adhesive will not work properly on the rough brick surfaces, for adhesive, the brick should be dense and smooth. For uneven surfaces, nails, anchors, or slips are more beneficial.
Can I Hang a Picture on a Brick Wall?
Undoubtedly hanging pictures will enhance the beauty of the brick wall, although sometimes the job might be hard to be done.
For an owner drilling permanent holes for hanging pictures might be convenient and a good option but for tenants sticking with adhesive hooks or mounting tape can be a good option as they are temporary attachments.
While working with brick walls you will have to keep in mind both brick as well as mortar. Proper inspection of brick walls is required before starting any work
For flat and dense brick walls, tapes, adhesive hooks, and anchors will be beneficial. For old, brittle bricks, the adhesive won’t be effective as they might not stick.
When mortar has higher strength than poor-quality brick then the picture needs to be hung on mortar rather than brick. For fireplace bricks, the adhesive will lose strength with the passage of time.
Where to Hang Your Picture?
The right location should be chosen beforehand for hanging the picture. This point is important since some methods of hanging the pictures are permanent in nature, so the position should be properly selected.
The decision of where to hang the picture can be tiring, but interior designers can be helpful. While hanging one or more than one frame, it should be placed at the center of attention. The center point of the picture should be kept at eye level, they must not be too high or too low.
For testing out the places, one method can be used, a printout can be taken out of the picture to be hung then with the help of tape it can be placed on the wall to get a preliminary idea of how the picture will look. is the picture in perfect position and all that?
The position and layout of furniture also matter, because their position might not be the same in the future, so the picture should be placed in such a way that with the change in position of furniture, the position need not be changed.
How to Hang a Picture on a Brick Wall Without Drilling Using Just a Nail?
Just a nail can be enough for hanging pictures on brick walls. Brick walls having mortar on them are different from plaster or concrete, mortar being easily replaceable and crack resistant becomes very useful for hanging pictures.
A nail having high strength to carry the weight of the picture frame is to be found. The nail should not be large enough. The nail should be placed at the bottom edge of the mortar, so that portion of the nail touches the brick.
The nail to be used should not be too long such that it penetrates the wall at just a perfect length to penetrate the brick and the required length flushing out from brick or mortar must be used.
- A hammer and nails are essential for hanging the frame.
- Tape for measurement, chalk, or pencil for marking.
The Layout of the Frame
The frame to be hung is positioned, then marking is done of the hanging spot. On the hanging spot, the nails are to be placed. This placement must be done at the bottom of the mortar.
The Nail Is to Be Driven
By applying adequate pressure, the nail is to be tapped with a hammer, going slow is the best option. Hard whacks will do nothing but increase the risk of cracks occurring.
Finally, Hang and Adjust
After placing the nail, hang your required picture and adjust.