Different Between Clamp Burning and Kiln Burning | What Is Clamp Burning | What IS Kiln Burning

What Is Clamp Burning?

A typical clamp is shown below figure The bricks and fuel are placed in alternate layers. The amount of fuel is reduced successively in the top layers.

Clamp Burning

Each brick tier consists of 4–5 layers of bricks. Some space is left between bricks for the free circulation of hot gasses. After 30 percent loading of the clamp, the fuel in the lowest layer is fired and the remaining loading of bricks and fuel is carried out hurriedly.

The top and sides of the clamp are plastered with mud. Then a coat of cow dung is given, which prevents the escape of heat.

The production of bricks is 2–3 lacs and the process is completed in six months. This process yields about 60 percent of first-class bricks.

Advantages of Clamp Burning

• Bricks produced are tough and hard due to gradual burning and cooling processes.

• It is Cheap and economical

• No skilled labour or supervision is required for the construction of clamps.

• There is lot of saving in fuel.

Disadvantage of Clamp Burning 

• Bricks produced are of irregular shape due to the settlement of bricks on turning of fuel to ashes.

• It is a slow process and flame regulation is not possible

• Quality of bricks is not uniform. Bricks at bottom, are found overburnt, while at top and sides are found to be under burnt.

Also, read: What Is Fine Aggregate | Types of Fine Aggregates (Classification)

What Is Kiln Burning?

The kiln used for burning bricks may be underground, e.g. Bull’s trench kiln or overground, e.g. Hoffman’s kiln. These may be rectangular, circular, or oval in shape.

When the process of burning bricks is continuous, the kiln is known as a continuous kiln, e.g. Bull’s trench and Hoffman’s kilns.

On the other hand, if the process of burning bricks is discontinuous, the kiln is known as an intermittent kiln.

Type of Kiln Burning 

• Intermittent Kiln

• Continuous Kiln

Intermittent Kiln

Continuous Kiln

Also, read: Mivan Shuttering | Merit & Demerit Mivan Technology | Mivan Formwork Assembly Process

Clamp Burning Vs Kiln Burning

Sr.No.	Particulars of Comparison	Clamp Burning	Kiln Burning
1	Initial cost	Initial cost is low	Initial cost is high
2	Type of structure	Clamps are tempray	Kilns are permanent structure
3	Daily output	25,000 to 1,00,000 bricks be burnt depending upon size of clamp.	25,00 bricks can be burnt continuosly daily.
4	Quality of bricks	Average 60% quality bricks obtained.	Average 90% quality bricks can be obtained.
5	Fire regulation	Controlled firing can not be maintained throughout the process.	Controlled firing can be be maintained through the processes.
6	Cost of fuel consumption	Less, because local fuel materials like stores etc can be used.	Cost of fuel consumption is high, because only coal is used as the fuel.
7	Brining period	2 to 6 months are necessary for burning and cooling.	Only about one day is necessary for burning and about 10 to 12 days for cooling of one chamber.
8	Preferability	Preferable for a small quantity and ordinary bricks.	Preferable for large, and continuous quality and pf quality production desired.
9	Wastage of heat	More wastage of heat because fire controlling and proper regulation is not possible.	Minimum wastage of heat because of proper heat regulation system.
10	Supervision	Supervision is not necessary	Skilled and continuous supervision is necessary.
11	Operations	Only burning of bricks is done.	Dry, heating and cooling operations are done sequentially.

Like this post? Share it with your friends!

Suggested Read –

• West Point Bridge Designer
• Introduction of USCS | USCS Classifies Soils into Two Broad Categories
• Introduction of Gantry Girder | Load on Gantry Gutter | Type of Load on Gantry Gutter
• What Is Pier Foundation | Types of Drilled Piers | Advantages and Disadvantages of Drilled Pier Foundations